Each device is controlled by TTL/CMOS input levelsand can be used as a bilateral switch or multiplexer/demultiplexer.
Low off leakage current (100pA for the MAX4066A) andlow power consumption (0.5µW) make the MAX4066/MAX4066A ideal for battery-operated equipment. Theseparts are also suitable for low-distortion audio applica-tions. Both devices are available in 14-pin DIP and SOpackages, as well as a 16-pin QSOP. ESD protection isgreater than 2000V per Method 3015.7.
____________________________FeaturesoPin Compatible with 74HC4066
oGuaranteed On-Resistance:
170Ωmax (3V supply)45Ωmax (12V supply)
oGuaranteed Match Between Channels:
4Ωmax (MAX4066)2Ωmax (MAX4066A)
oGuaranteed Low Leakage Currents:
1nA at +25°C (MAX4066)100pA at +25°C (MAX4066A)
oSingle-Supply Operation from +2.0V to +16VoV+ to GND Signal Handling oTTL/CMOS-Logic CompatibleoLow Power Consumption: 0.5µWoLow Crosstalk: -86dBMAX4066/MAX4066AoLow Off Isolation: -58dB________________________ApplicationsoLow Distortion: 0.03% oWide Bandwidth: > 100MHz
Battery-Operated EquipmentAudio and Video Signal Routing______________Ordering InformationLow-Voltage Data-Acquisition SystemsPARTTEMP. RANGEPIN-PACKAGESample-and-Hold CircuitsMAX4066CPD0°C to +70°C14 Plastic DIPCommunication Circuits
MAX4066CSD0°C to +70°C14 Narrow SOMAX4066CEE0°C to +70°C16 QSOPMAX4066C/D0°C to +70°CDice*Ordering Information continued at end of data sheet.* Contact factory for dice specifications.______________________________________________Pin Configurations/Truth TableTOP VIEWNO1114V+NO1116V+COM1213IN1TRUTH TABLECOM1215IN1NO2312IN4ON/OFF CONTROLSTATE OFINPUTANALOG SWITCHN.C.314IN4COM24NO4IN25MAX4066AMAX406611LOFFNO2410COM4HONCOM25MAX4066AMAX406613NO412COM4IN369COM3IN2611N.C.GND78NO3IN3710COM3GND89NO3DIP/SON.C. = NO INTERNAL CONNECTIONQSOP________________________________________________________________Maxim Integrated Products1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800元器件交易网www.cecb2b.comLow-Cost, Low-Voltage, Quad, SPST, CMOS Analog SwitchesMAX4066/MAX4066AABSOLUTE MAXIMUM RATINGS
(Voltages referenced to GND)
V+...........................................................................-0.3V to +17VVIN_, VCOM_, VNO(Note 1)...........................-0.3V to (V + +0.3V)Current (any terminal).........................................................30mAPeak Current (any terminal)..............................................100mAESD per Method 3015.7..................................................>2000VContinuous Power Dissipation (TA= +70°C)
Plastic DIP (derate 10.00mW/°C above +70°C)............800mWNarrow SO (derate 8.00mW/°C above +70°C)..............640mWQSOP (derate 9.52mW/°C above +70°C)......................762mW
CERDIP (derate 9.09mW/°C above +70°C)....................727mWOperating Temperature Ranges
MAX4066C_ _/MAX4066AC_ _.............................0°C to +70°CMAX4066E_ _/MAX4066AE_ _...........................-40°C to +85°CMAX4066MJD/MAX4066AMJD.......................-55°C to +125°CStorage Temperature Range.............................-65°C to +150°CLead Temperature (soldering, 10sec).............................+300°C
Note 1:Signals on NO_, COM_, or IN_ exceeding V+ or GND are clamped by internal diodes. Limit forward-diode current to
maximum current rating.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functionaloperation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure toabsolute maximum rating conditions for extended periods may affect device reliability.ELECTRICAL CHARACTERISTICS—Single +12V Supply
(V+ = 12V ±10%, GND = 0V, VINH= 4.0V, VINL= 0.8V, TA= TMINto TMAX, unless otherwise noted.)
PARAMETERANALOG SWITCHAnalog Signal RangeVCOM,VNORON(Note 3)V+ = 12V,ICOM= 2mA,VNO= 10VV+ = 12V,ICOM= 2mA,VNO= 10VTA= +25°CTA= TMINto TMAXTA= +25°CC, EMMAX4066MAX4066A0.50.5016V+45557542624ΩTA= TMINto TMAXTA= +25°CTA= TMINto TMAXTA= +25°CTA= TMINto TMAXTA= +25°CTA= TMINto TMAXMAX4066MAX4066AC, EMMAX4066MAX4066AC, EMMAX4066MAX4066AC, EM-1-0.1-6-100-1-0.1-6-100-2-0.2-12-200610.1610010.1610020.212200nAnAnAΩΩVSYMBOLCONDITIONSMINTYP(Note 2)MAXUNITSOn-ResistanceOn-Resistance MatchBetween Channels (Note 4)∆RONTA= TMINto TMAXTA= +25°COn-Resistance Flatness (Note 5)V+ = 12V,RFLAT(ON)ICOM= 2mA,VNO= 10V, 5V, 1VV+ = 12V,VCOM= 0V,VNO= 10VNO or NC Off LeakageCurrent (Note 6)INO(OFF)COM Off Leakage Current(Note 6)V+ = 12V,ICOM(OFF)VCOM= 0V,VNO= 10VCOM On Leakage Current(Note 6)ICOM(ON)V+ = 12V,VCOM= 10V,VNO= 10V2_______________________________________________________________________________________
元器件交易网www.cecb2b.comLow-Cost, Low-Voltage, Quad, SPST, CMOS Analog SwitchesELECTRICAL CHARACTERISTICS—Single +12V Supply (continued)
(V+ = 12V ±10%, GND = 0V, VINH= 4.0V, VINL= 0.8V, TA= TMINto TMAX, unless otherwise noted.)
PARAMETERLOGIC INPUTInput Current with InputVoltage HighInput Current with InputVoltage LowDYNAMICTurn-On TimeTurn-Off TimeOn-Channel BandwidthCharge InjectiontONtOFFBWVCOM= 10V, Figure 2VCOM= 10V, Figure 2Signal = 0dbm, Figure 4,50Ωin and outCL= 1.0nF, VGEN= 0V,TA= +25°CTA= TMINto TMAXTA= +25°CTA= TMINto TMAXTA= +25°C100152510015075100nsnsMHzIINHIINLIN = 5.0V, all others = 0.8VIN = 0.8V, all others = 5.0V-0.5-0.50.0050.0050.50.5µAµASYMBOLCONDITIONSMINTYP(Note 2)MAXUNITSMAX4066/MAX4066A(Note 3)VCTERGEN= 0Ω, Figure 3TA= +25°C110pCOff Isolation (Note 7)VISORL= 50Ω, CL= 5pF,f = 1MHz, Figure 4TA= +25°C-58dBCrosstalk (Note 8)VCTRL= 50Ω, CL= 5pF,f = 1MHz, Figure 5TA= +25°C-86dBNO CapacitanceC(OFF)f = 1MHz, Figure 6TA= +25°C9pFCOM Off CapacitanceCCOM(OFF)f = 1MHz, Figure 6TA= +25°C9pFCOM On CapacitanceCCOM(ON)f = 1MHz, Figure 6TA= +25°C22pFSUPPLYPower-Supply RangeVSupply CurrentI+VIN= 0V or V+,all channels on or offTA= TMINto TMAX-10.0011µATotal HarmonicDistortionTHDTA= TMINto TMAX0.03%_______________________________________________________________________________________3
元器件交易网www.cecb2b.comLow-Cost, Low-Voltage, Quad, SPST, CMOS Analog SwitchesMAX4066/MAX4066AELECTRICAL CHARACTERISTICS—Single +5V Supply
(V+ = 5V ±10%, V- = 0V ±10%, GND = 0V, VINH= 2.4V, VINL= 0.8V, TA= TMINto TMAX, unless otherwise noted.)
PARAMETERANALOG SWITCHAnalog Signal RangeVCOM,VNO(Note 3)V+ = 4.5V,ICOM= -1.0mA,VNO= 3.5VV+ = 5V,ICOM= -1.0mA,VNO= 3VTA= +25°CTA= TMINto TMAXTA= +25°CTA= TMINto TMAXTA= +25°CTA= TMINto TMAXTA= +25°CTA= TMINto TMAXTA= +25°CTA= TMINto TMAXTA= +25°CTA= TMINto TMAXTA= +25°CTA= TMINto TMAXTA= +25°CTA= TMINto TMAX100TA= +25°C21018MAX4066MAX4066AC, EMMAX4066MAX4066AC, EMMAX4066MAX4066AC, EM-1-0.1-6-100-1-0.1-6-100-2-0.2-12-200434C, EM0.304552V+751001254126810.1610010.1610020.21220012517575125nAnAnAΩΩVSYMBOLCONDITIONSMINTYP(Note 2)MAXUNITSOn-ResistanceRONOn-Resistance MatchBetween Channels (Note 4)On-Resistance Flatness(Notes 3, 5)∆RONV+ = 5V,RFLAT(ON)ICOM= -1.0mA,VNO= 1V, 3VV+ = 5.5V,VCOM= 0V,VNO= 4.5VΩNO Off Leakage Current (Note 6)INO(OFF)COM Off Leakage Current(Note 6)V+ = 5.5V,ICOM(OFF)VCOM= 0V,VNO= 4.5VCOM On Leakage Current(Note 6)DYNAMICTurn-On TimeTurn-Off TimeOn-ChannelBandwidthCharge Injection(Note 3)SUPPLYPositive Supply CurrentICOM(ON)V+ = 5.5V,VCOM= 5V,VNO= 4.5VtONtOFFBWQVNO = 3VVNO = 3VSignal = 0dBm,50Ωin and out, Figure 4VGEN= 0V, RGEN= 0V,CL= 1.0nF, Figure 3nsnsMHzpCI+V+ = 5.5V, VIN= 0V or V+, all channels on or off-11µA4_______________________________________________________________________________________
元器件交易网www.cecb2b.comLow-Cost, Low-Voltage, Quad, SPST, CMOS Analog SwitchesELECTRICAL CHARACTERISTICS—Single +3V Supply
(V+ = 2.7V to 3.3V ±10%, GND = 0V, VINH= 2.4V, VINL= 0.8V, TA= TMINto TMAX, unless otherwise noted.)
PARAMETERANALOG SWITCHAnalog Signal RangeVCOM,VNORON(Note 3)V+ = 3V,ICOM= -1.0mA,VNO= 1.5VV+ = 3V,VNOor VNC= 1.5VV+ = 3V,VNOor VNC= 1.5VCL= 1.0nF, VGEN= 0V, RGEN= 0VTA= +25°CTA= TMINto TMAXTA= +25°CTA= TMINto TMAXTA= +25°CTA= TMINto TMAXTA= +25°C228800V+17022518523015020010VSYMBOLCONDITIONSMINTYP(Note 2)MAXUNITSMAX4066/MAX4066AChannel On-ResistanceDYNAMICTurn-On Time (Note 3)Turn-Off Time (Note 3)Charge Injection (Note 3)ΩtONtOFFQnsnspCSUPPLYPositive Supply CurrentI+V+ = 3.6V, VIN= 0V or V+, all channels on or off-10.0011µANote 2:The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in
this data sheet.
Note 3:Guaranteed by design.
Note 4:∆RON= RON(max) - RON(min).
Note 5:Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the
specified analog signal range.
Note 6:Leakage parameters are 100% tested at maximum-rated hot temperature and guaranteed by correlation at +25°C.Note 7:Off Isolation = 20log10(VCOM/ VNO), VCOM= output, VNO= input to off switch.Note 8:Between any two switches.
_______________________________________________________________________________________5
元器件交易网www.cecb2b.comLow-Cost, Low-Voltage, Quad, SPST, CMOS Analog SwitchesMAX4066/MAX4066A__________________________________________Typical Operating Characteristics(TA = +25°C, unless otherwise noted.)
ON-RESISTANCE vs. VCOM AND
TEMPERATURE
MAX4066-01MAX4066-02ON-RESISTANCE vs. VCOM
150140120
A100RON (Ω)806040200
0
2
4
6
8
10
12
14
16
VCOM (V)
BCDE100
0
A: V+ = 2.5VB: V+ = 3.0VC: V+ = 5VD: V+ = 10VE: V+ = 15VV- = 0V605040RON (Ω)3020
OFF LEAKAGE CURRENTvs. TEMPERATURE
V+ = 5.5VVCOM = 0VVNO = 4.5VMAX4066-0310010OFF LEAKAGE (nA)10.10.010.0010.0001
-75-50
DCBAA: TA = -55°CB: TA = +25°CC: TA = +85°CD: TA = +125°CV+ = 5V246810121416-25
VCOM (V)
2550750
TEMPERATURE (°C)
100125
ON LEAKAGE CURRENTvs. TEMPERATURE
MAX4066-04CHARGE INJECTION
vs. VCOM
A: V+ = 12VB: V+ = 5VC: V+ = 3VI+ (µA)B0-2-4-6
CAMAX4066-05SUPPLY CURRENTvs. TEMPERATURE
V+ = 5.5V1010.10.01
0.0010.0001
-75-50
I+MAX4066-0610010ON LEAKAGE (nA)10.10.010.001
0.0001
-75-50-25
642
VCTE (pC)100
5075
TEMPERATURE (°C)
0251001250246VCOM (V)
81012-25
2550750
TEMPERATURE (°C)
100125
MAX4066-07ON RESPONSE-10-20LOSS (dB)-30-40-50-60
1
10
FREQUENCY (MHz)
100
V+ = 5VINPUT = 0dBm50Ω IN AND OUTON PHASEOFF ISOLATION40200-20-40-60
0.01
10
PHASE (degrees)10THD (%)V+ = 12V5Vp-p SIGNAL600Ω IN AND OUT1
0.1
3001001k10k20k
FREQUENCY (Hz)
6_______________________________________________________________________________________
MAX4066-080
FREQUENCY RESPONSE
TOTAL HARMONIC DISTORTION vs. FREQUENCY
60
100
元器件交易网www.cecb2b.comLow-Cost, Low-Voltage, Quad, SPST, CMOS Analog Switches______________________________________________________________Pin DescriptionPIN
DIP/SO1, 3, 8, 112, 4, 9, 10
—13, 5, 6, 12
714
QSOP1, 4, 9, 132, 5, 10, 123, 1115, 6, 7, 14
816
NAMENO1–NO4COM1–COM4
N.C.IN1–IN4GNDV+
FUNCTION
Analog Switch Normally Open Terminal (bidirectional)Analog Switch Common Terminal (bidirectional)Not internally connectedLogic Control InputsGround
Positive Supply Voltage
MAX4066/MAX4066A__________Applications InformationOvervoltage ProtectionProper power-supply sequencing is recommended forall CMOS devices. Do not exceed the absolute maxi-POSITIVE SUPPLYmum ratings, because stresses beyond the listed rat-ings may cause permanent damage to the devices.MAX4066Always sequence V+ on first, followed by the logicV+MAX4066Ainputs. If power-supply sequencing is not possible, addtwo small signal diodes in series with supply pins forovervoltage protection (Figure 1). Adding diodesreduces the analog signal range to 1V below V+ andNOCOM1V above GND, but low switch resistance and low leak-age characteristics are unaffected. Device operation isunchanged, and the difference between V+ and GNDVgshould not exceed 17V.
Figure 1. Overvoltage Protection Using Two External BlockingDiodes_______________________________________________________________________________________7
元器件交易网www.cecb2b.comLow-Cost, Low-Voltage, Quad, SPST, CMOS Analog SwitchesMAX4066/MAX4066A______________________________________________Test Circuits/Timing DiagramsMAX4066MAX4066ASWITCHINPUTVCOMV+V+COMNORL300ΩGNDSWITCHOUTPUT0VtON0VSWITCHOUTPUTVOUTCL35pFVOUTLOGICINPUTVINH0V50%tR < 20nstF < 20nsINLOGICINPUTtOFF0.9 x V0UT0.9 x VOUTCL INCLUDES FIXTURE AND STRAY CAPACITANCE. RL VOUT = VCOM RL + RON()Figure 2. Switching TimeMAX4066MAX4066AV+V+RGENCOMNO CLGNDIN OFFONQ = (∆VOUT)(CL)VOUT ∆VOUTVOUT VGENINVINOFFFigure 3. Charge Injection8_______________________________________________________________________________________
元器件交易网www.cecb2b.comLow-Cost, Low-Voltage, Quad, SPST, CMOS Analog Switches____________________________________________________Test Circuits (continued)MAX4066/MAX4066A10nFSIGNALGENERATOR 0dBmV+MAX4066MAX4066ASIGNALGENERATOR 0dBmVINL ORVINH10nFV+MAX4066MAX4066ACOMV+V+COM1IN1N01IN250ΩIN ANALYZERRLCOMNOGNDVINL ORVINHANALYZERRLVINL ORVINHN02GNDCOM2Figure 4. Off Isolation/On-Channel BandwidthFigure 5. Crosstalk10nFV+MAX4066MAX4066AV+COMCAPACITANCEIN VINL ORMETERVINHNOf = 1MHzGNDFigure 6. Channel Off/On Capacitance_______________________________________________________________________________________9
元器件交易网www.cecb2b.comLow-Cost, Low-Voltage, Quad, SPST, CMOS Analog SwitchesMAX4066/MAX4066A_Ordering Information (continued)PARTMAX4066EPDMAX4066ESDMAX4066MJDMAX4066ACPDMAX4066ACSDMAX4066ACEEMAX4066AC/DMAX4066AEPDMAX4066AESDMAX4066AEEEMAX4066AMJDTEMP. RANGE-40°C to +85°C-40°C to +85°C-55°C to +125°C0°C to +70°C0°C to +70°C0°C to +70°C0°C to +70°C-40°C to +85°C-40°C to +85°C-40°C to +85°C-55°C to +125°CPIN-PACKAGE14 Plastic DIP14 Narrow SO14 CERDIP**14 Plastic DIP14 Narrow SO16 QSOPDice*14 Plastic DIP14 Narrow SO16 QSOP14 CERDIP**NO2COM2
NO4COM40.108\"(2.74mm)COM1
___________________Chip TopographyNO1 V+ IN1IN4* Contact factory for dice specifications.** Contact factory for availability.IN2
COM3IN3GND0.065\"(1.65mm)NO3TRANSISTOR COUNT: 69SUBSTRATE CONNECTED TO V+
10______________________________________________________________________________________
元器件交易网www.cecb2b.comLow-Cost, Low-Voltage, Quad, SPST, CMOS Analog Switches________________________________________________________Package InformationEDA3AA2E1DIMAA1A2A3BB1CD1EE1eeAeBLINCHESMAXMIN0.200––0.0150.1750.1250.0800.0550.0220.0160.0650.0450.0120.0080.0800.0050.3250.3000.3100.240–0.100–0.3000.400–0.1500.115MILLIMETERSMINMAX–5.080.38–3.184.451.402.030.410.561.141.650.200.300.132.037.628.266.107.872.54–7.62––10.162.923.81MILLIMETERSMINMAXMAX4066/MAX4066ALA1eBD10° - 15°CB1eAeBPlastic DIPINCHESPKG.DIMPINSMINMAXPLASTICPD80.3480.3908.849.91DUAL-IN-LINEPD140.7350.76518.6719.43PACKAGEPD160.7450.76518.9219.43(0.300 in.)PD180.8850.91522.4823.24PD201.0151.04525.7826.54ND241.141.26528.9632.1321-0043ADIMINCHESMILLIMETERSMINMAXMINMAXDA0.0530.0691.351.75A10.0040.0100.100.250°-8°B0.0140.0190.350.49AC0.0070.0100.190.25E0.1500.1573.804.000.101mm0.004in.e0.0501.27eA1CH0.2280.2445.806.20BLL0.0160.0500.401.27Narrow SODIMINCHESMILLIMETERSPINSMINMAXMINMAXEHSMALL-OUTLINED80.1890.1974.805.00PACKAGED140.3370.3448.558.75(0.150 in.)D160.3860.3949.8010.0021-0041A______________________________________________________________________________________11
元器件交易网www.cecb2b.comLow-Cost, Low-Voltage, Quad, SPST, CMOS Analog SwitchesMAX4066/MAX4066A___________________________________________Package Information (continued)INCHESMILLIMETERSDIMMAXMINMINMAXA0.0680.0611.551.73A10.0040.00980.1270.25A20.0550.0611.401.55B0.0120.0080.200.31C0.00750.00980.190.25SEE VARIATIONSDE0.1570.1503.813.990.635 BSCe0.25 BSCH0.2440.2305.846.20h0.0160.0100.250.41L0.0350.0160.410.89SEE VARIATIONSNSSEE VARIATIONSα8°0°0°8°INCHESMILLIMETERSDIMPINSMINMAXMINMAX160.1890.1964.804.98D160.00200.00700.050.18S200.3370.3448.568.74D200.05000.05501.271.40S240.3370.3448.568.74D240.02500.03000.640.76S280.3860.3939.809.98D280.02500.03000.640.76S21-0055ADAeBA1SEHh x 45°A2αNECLQSOPQUARTERSMALL-OUTLINEPACKAGEMaxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses areimplied. Maxim reserves the right to change the circuitry and specifications without notice at any time.12__________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600©1996 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
因篇幅问题不能全部显示,请点此查看更多更全内容