AM26LS32AC, AM26LS33AC, AM26LS32AM, AM26LS33AMQUADRUPLE DIFFERENTIAL LINE RECEIVERS SLLS115B – OCTOBER 1980 – REVISED MAY 1995DAM26LS32A Meets or Exceeds theDDDDDDDDD Requirements of ANSI EIA/TIA-422-B,EIA/TIA-423-B, and ITU RecommendationsV.10 and V.11AM26LS32A Has ±7-V Common-ModeRange With ±200-mV SensitivityAM26LS32A Has ±15-V Common-ModeRange With ±500-mV SensitivityInput Hysteresis...50mVTypicalOperates From a Single 5-V SupplyLow-Power Schottky Circuitry3-State OutputsComplementary Output Enable InputsInput Impedance...12kΩ MinDesigned to Be Interchangeable WithAdvanced Micro Devices AM26LS32™ andAM26LS33™AM26LS32AC, AM26LS33AC...D OR N PACKAGEAM26LS32AM, AM26LS33AM...JPACKAGE(TOP VIEW)1B1A1YG2Y2A2BGND12345678161514131211109VCC4B4A4YG3Y3A3BAM26LS32AM, AM26LS33AM...FK PACKAGE(TOP VIEW)1A1BNCVCC4B1YGNC2Y2A4567832120191817161514910111213descriptionThe AM26LS32A and AM26LS33A are quadrupledifferential line receivers for balanced andunbalanced digital data transmission. The enablefunction is common to all four receivers and offersa choice of active-high or active-low input. The3-state outputs permit connection direct to a bus-organized system. Fail-safe design ensures thatif the inputs are open, the outputs are always high.4A4YNCG3YNC–No internal connectionCompared to the AM26LS32 and the AM26LS33, the AM26LS32A and AM26LS33A incorporate an additionalstage of amplification to improve sensitivity. The input impedance has been increased resulting in less loadingof the bus line. The additional stage has increased propagation delay; however, this does not affectinterchangeability in most applications.The AM26LS32AC and AM26LS33AC are characterized for operation from 0°C to 70°C. The AM26LS32AMand AM26LS33AM are characterzed for operation over the full military temperature range of –55°C to 125°C.Please be aware that an important notice concerning availability, standard warranty, and use in critical applications ofTexasInstruments semiconductor products and disclaimers thereto appears at the end of this data sheet.AM26LS32 and AM26LS33 are trademarks of Advanced Micro Devices, Inc.PRODUCTION DATA information is current as of publication date.Products conform to specifications per the terms of Texas Instrumentsstandard warranty. Production processing does not necessarily includetesting of all parameters.Copyright © 1995, Texas Instruments IncorporatedPOST OFFICE BOX 655303 DALLAS, TEXAS 75265•2BGNDNC3B3A1SLLS115B – OCTOBER 1980 – REVISED MAY 1995AM26LS32AC, AM26LS33AC, AM26LS32AM, AM26LS33AMQUADRUPLE DIFFERENTIAL LINE RECEIVERS FUNCTION TABLE(each receiver)DIFFERENTIALA – BVID ≥ VVIT+ITVIT– ≤ VVID ≤ VVIT+ITVID ≤ VIT–XOpenENABLESGHXHXHXLHXGXLXLXLHXLOUTPUTYHH??LLZHH H = high level, L = low level, ? = indeterminate, X = irrelevant, Z = high impedance (off)logic symbol†GG412≥ 1ENlogic diagram (positive logic)GG4121A1A1B2167109113Y31Y1B2A2A2B3A3B52Y3A3B2B216731Y52Y109113Y4A4B14154A134Y4B1415134Y†This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.Pin numbers shown are for D, J, and N packages.2POST OFFICE BOX 655303 DALLAS, TEXAS 75265• AM26LS32AC, AM26LS33AC, AM26LS32AM, AM26LS33AMQUADRUPLE DIFFERENTIAL LINE RECEIVERS SLLS115B – OCTOBER 1980 – REVISED MAY 1995schematics of inputs and outputsEQUIVALENT OF EACHDIFFERENTIAL INPUTVCC100 kΩ A Input OnlyEQUIVALENT OF EACH ENABLE INPUTVCC8.3 kΩNOMTYPICAL OF ALL OUTPUTSVCC85 ΩNOM20 kΩNOMInput960 ΩNOMOutputEnable960 ΩNOM100 kΩ B Input Onlyabsolute maximum ratings over operating free-air temperature range (unless otherwise noted)†Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 VInput voltage VI:any differential input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25 Vother inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 VDifferential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25 VContinuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating TableOperating free-air temperature range, TA:AM26LS32AC 0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . °C to 70°CAM26LS33AC 0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . °C to 70°CAM26LS32AM –40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . °C to 85°CAM26LS33AM –40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . °C to 85°CStorage temperature range, Tstg –65. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . °C to 150°CLead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D or N package . . . . . . . . . . . . . . . . 260°CCase temperature for 60 seconds, TC: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°CLead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J package . . . . . . . . . . . . . . . . . . . . . 300°C†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, andfunctional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is notimplied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.NOTES:1.All voltage values, except differential voltages, are with respect to the network ground terminal.2.Differential voltage values are at the noninverting (A) input terminals with respect to the inverting (B) input terminals.DISSIPATION RATING TABLEPACKAGEDFKJNTA ≤ 25°CPOWER RATING950 mW1375 mW1375 mW1150 mWDERATING FACTORABOVE TA = 25°C7.6 mW/°C11.0 mW/°C11.0 mW/°C9.2 mW/°CTA = 70°CPOWER RATING608 mW880 mW880 mW736 mWTA = 125°CPOWER RATING—275 mW275 mW—POST OFFICE BOX 655303 DALLAS, TEXAS 75265•3SLLS115B – OCTOBER 1980 – REVISED MAY 1995AM26LS32AC, AM26LS33AC, AM26LS32AM, AM26LS33AMQUADRUPLE DIFFERENTIAL LINE RECEIVERS recommended operating conditionsAM26LS32ACAM26LS33ACMINSupply voltage, VCCHigh-level input voltage, VIHLow-level input voltage, VILCommonmodeinputvoltageVICCommon-mode input voltage, VHigh-level output current, IOHLow-level output current, IOLOperating free-air temperature, TA0AM26LS32AC, AM26LS32AMAM26LS33AC, AM26LS33AM4.7520.8±7±15–440870–55NOM5MAX5.25AM26LS32AMAM26LS33AMMIN4.520.8±7±15–4408125NOM5MAX5.5VVVVµAmA°CUNIT electrical characteristics over recommended ranges of VCC, VIC, and operating free-airtemperature (unless otherwise noted)PARAMETERVIT+VIT–VhysVIKVOHVOLIOZIIII(EN)IIHIILrIIOSPositivegoinginputthreshholdvoltagePositive-going input threshhold voltageNegativegoinginputthreshholdvoltageNegative-going input threshhold voltageHysteresis voltage (VIT+ – VIT–)Enable input clamp voltageHighleveloutputvoltageHigh-level output voltageLowleveloutputvoltageLow-level output voltageOff-state (high-impedance-state) output(g)currentLineinputcurrentLine input currentEnable input currentHigh-level enable currentLow-level enable currentInput resistanceShort-circuit output current§TEST CONDITIONSVO = V=VOHminmin,VO = 0.45 V,=045VIOH = –=440 440µAIOL = 8 mA=8mAAM26LS32AAM26LS33AAM26LS32AAM26LS33A–0.2‡–0.5‡50VCC = MIN,VCC = MIN,,VI(G) = 0.8 V,VCC = MIN,,VI(G) = 0.8 VVCC = MAX=MAXVI = 15 V,VI = –15 V,VI = 5.5 VVI = 2.7 VVI = 0.4 VVIC = –15 V to 15 V, One input to ac groundVCC = MAX12–1515–85II = –18 mAVID = 1 V,,IOH = –440 µAVID = –1 V, , ’32AC, ’33AC’32AM, ’33AMIOL = 4 mAIOL = 8 mAVO = 2.4 VVO = 0.4 VOther input at –10 V to 15 VOther input at –15 V to 10 V2.72.50.40.4520–201.2–1.710020–0.36–1.5MINTYP†MAX0.20.5UNITVVmVVVVµAmAµAµAmAkΩmAICCSupply currentVCC = MAX,All outputs disabled5270mA†All typical values are at VCC = 5 V, TA = 25°C, and VIC = 0.‡The algebraic convention, in which the less positive (more negative) limit is designated as minimum, is used in this data sheet for threshold levelsonly.§Not more than one output should be shorted to ground at a time, and duration of the short circuit should not exceed one second.4POST OFFICE BOX 655303 DALLAS, TEXAS 75265• AM26LS32AC, AM26LS33AC, AM26LS32AM, AM26LS33AMQUADRUPLE DIFFERENTIAL LINE RECEIVERS SLLS115B – OCTOBER 1980 – REVISED MAY 1995switching characteristics, VCC = 5 V, TA = 25°CPARAMETERtPLHtPHLtPZHtPZLtPHZtPLZPropagation delay time, low-to-high-level outputPropagation delay time, high-to-low-level outputOutput enable time to high levelOutput enable time to low levelOutput disable time from high levelOutput disable time from low levelTEST CONDITIONS=15pFCL = 15 pF,CL = 15 pF,=15pFCL = 5 pF,=5pFSeeFigure1See Figure 1SeeFigure1See Figure 1SeeFigure1See Figure 1MINTYP202217202130MAX353522253040UNITnsnsnsnsnsnsPARAMETER MEASUREMENT INFORMATIONTestPointVCCRL = 2 kΩS1From OutputUnder TestCL(see Note A) 2.5 VInputtPLH5 kΩSee Note BS2TEST CIRCUITVOLTAGE WAVEFORMS FOR tPLH, tPHLOutput00tPHL1.3 V1.3 V– 2.5 VVOHVOLS1 and S2 Closed≤5 ns90%Enable G10%See Note C90%1.3 VEnable GtPZHOutputS1 OpenS2 Closed1.3 VtPHZVOLTAGE WAVEFORMS FOR tPHZ, tPZH10%10%1.3 V90%1.3 V≤5 ns3 VEnable G10%03 V10%≤5 ns90%1.3 V90%1.3 V≤5 ns3 V10%See Note C03 V90%1.3 V90%Enable G1.3 V10%tPZL10%90%1.3 V00.5 VVOHOutput≈1.4 VS1 ClosedS2 ClosedS1 ClosedS2 ClosedtPLZ0.5 V0≈1.4 VVOL1.3 VS1 ClosedS2 OpenVOLTAGE WAVEFORMS FOR tPLZ, tPZLNOTES:A.CL includes probe and jig capacitance.B.All diodes are 1N3064 or equivalent.C.Enable G is tested with G high; G is tested with G low.Figure 1POST OFFICE BOX 655303 DALLAS, TEXAS 75265•5SLLS115B – OCTOBER 1980 – REVISED MAY 1995AM26LS32AC, AM26LS33AC, AM26LS32AM, AM26LS33AMQUADRUPLE DIFFERENTIAL LINE RECEIVERS TYPICAL CHARACTERISTICSHIGH-LEVEL OUTPUT VOLTAGEvsHIGH-LEVEL OUTPUT CURRENT†5VOH– High-Level Output Voltage – VVOH– High-Level Output Voltage – VVID = 0.2 VTA = 25°C45VCC = 5 VVID = 0.2 mVIOH = –440 µA HIGH-LEVEL OUTPUT VOLTAGEvsFREE-AIR TEMPERATURE43VCC = 5.25 VVCC = 5 V32VCC = 5.5 V1VCC = 4.75 V2100VCC = 4.5 V– 40– 10– 20– 30IOH – High-Level Output Current – mA– 5000102030405060TA – Free-Air Temperature – °C7080†VCC = 5.5 V and VCC = 4.5 V applies to M-suffix devices only.Figure 2LOW-LEVEL OUTPUT VOLTAGEvsLOW-LEVEL OUTPUT CURRENT0.6VOL– Low-Level Output Voltage – VVOL– Low-Level Output Voltage – VVCC = 5 VTA = 25°CVID = –0.2 mV0.5VCC = 5 VVID = –0.2 VIOL = 8 mAFigure 3LOW-LEVEL OUTPUT VOLTAGEvsFREE-AIR TEMPERATURE0.50.40.40.30.30.20.20.10.10010152025IOL – Low-Level Output Current – mA53000102030405060TA – Free-Air Temperature – °C7080Figure 4Figure 56POST OFFICE BOX 655303 DALLAS, TEXAS 75265• AM26LS32AC, AM26LS33AC, AM26LS32AM, AM26LS33AMQUADRUPLE DIFFERENTIAL LINE RECEIVERS SLLS115B – OCTOBER 1980 – REVISED MAY 1995TYPICAL CHARACTERISTICSOUTPUT VOLTAGEvsENABLE G VOLTAGE54.54VO– Output Voltage – V3.532.521.510.5000.511.522.53Enable G Voltage – VVID = 0.2 VTA = 25°CLoad = 8 kΩ to GND54.5VCC = 5.5 VVO– Output Voltage – VVCC = 5 VVCC = 4.5 V43.532.521.510.5000.511.522.53Enable G Voltage – VTA = 70°CTA = 25°CTA = 0°CVCC = 5 VVID = 0.2 VLoad = 8 kΩ to GNDOUTPUT VOLTAGEvsENABLE G VOLTAGEFigure 6OUTPUT VOLTAGEvsENABLE G VOLTAGE6VCC = 5.5 V5VO– Output Voltage – VVCC = 5 VVCC = 4.5 VVID = –0.2 VLoad = 1 kΩ to VCCTA = 25°CVO– Output Voltage – V6Figure 7OUTPUT VOLTAGEvsENABLE G VOLTAGE5TA = 0°CTA = 25°CTA = 70°C44332211000.511.522.53Enable G Voltage – V00VCC = 5 VVID = –0.2 VLoad = 1 kΩ to VCC0.511.522.53Enable G Voltage – VFigure 8Figure 9POST OFFICE BOX 655303 DALLAS, TEXAS 75265•7SLLS115B – OCTOBER 1980 – REVISED MAY 1995AM26LS32AC, AM26LS33AC, AM26LS32AM, AM26LS33AMQUADRUPLE DIFFERENTIAL LINE RECEIVERS TYPICAL CHARACTERISTICSAM26LS32AAM26LS33A OUTPUT VOLTAGEvsDIFFERENTIAL INPUT VOLTAGE54.54VO– Output Voltage – V3.532.521.510.50– 200– 150–100– 50050100150200VIT–VIT+VIT–VIT+VIT–VIT+OUTPUT VOLTAGEvsDIFFERENTIAL INPUT VOLTAGE5VCC = 5 V, IO = 0, TA = 25°CVCC = 5 VIO = 0TA = 25°CVIC =–7 VVIC =0VIC =7 V4.54VO– Output Voltage – V3.532.521.510.5VIC =–15 VVIC =0VIC =15 VVIT–VIT+VIT–VIT+VIT–VIT+0– 200– 150–100– 50050100150200VID – Differential Input Voltage – mVVID – Differential Input Voltage – mVFigure 10INPUT CURRENTvs INPUT VOLTAGE43210VCC = 0– 1– 2– 3– 4– 25–20–15–10– 5VCC = 5 VFigure 11II– Input Current – mAThe Unshaded AreaShows Requirements ofParagraph 4.2.1 of ANSIStandards EIA/TIA-422-B andEIA/TIA-423-B0510152025VI – Input Voltage – VFigure 128POST OFFICE BOX 655303 DALLAS, TEXAS 75265• AM26LS32AC, AM26LS33AC, AM26LS32AM, AM26LS33AMQUADRUPLE DIFFERENTIAL LINE RECEIVERS SLLS115B – OCTOBER 1980 – REVISED MAY 1995APPLICATION INFORMATION1/4 AM26LS31ACRT†1/4 AM26LS32ACDataOutData In1/4 AM26LS32ACDataOut1/4 AM26LS33ACDataOut†RT equals the characteristic impedance of the line.Figure 13. Circuit With Multiple ReceiversPOST OFFICE BOX 655303 DALLAS, TEXAS 75265•9IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinueany product or service without notice, and advise customers to obtain the latest version of relevant informationto verify, before placing orders, that information being relied on is current and complete. All products are soldsubject to the terms and conditions of sale supplied at the time of order acknowledgement, including thosepertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale inaccordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extentTI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarilyperformed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OFDEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICALAPPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, ORWARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHERCRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TOBE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operatingsafeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or representthat any license, either express or implied, is granted under any patent right, copyright, mask work right, or otherintellectual property right of TI covering or relating to any combination, machine, or process in which suchsemiconductor products or services might be or are used. TI’s publication of information regarding any thirdparty’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright © 1998, Texas Instruments Incorporated