ND3FC16P;NDFC16P;NDFR16P;NDFR10P;NDFR16H;中文规格书,Datasheet资料

RockersGeneral Specifications

Electrical Capacity (Resistive Load) Switching Rating: 100mA @ 5V DC

Nonswitching Rating:

Pushbuttons100mA @ 50V DC

Keylocks

Other Ratings

Contact Resistance: 80 milliohms maximum for circuit; 30 milliohms maximum for contact point Insulation Resistance: 1,000 megohms minimum @ 250V DC Dielectric Strength: 250V AC minimum for 1 minute minimum Mechanical Life: 20,000 detent operations minimum Electrical Life: 20,000 detent operations minimum

Notes: A detent operation is one actuator position operation or stepping.

20,000 detent operations = 1,250 cycles for hexadecimal devices or 2,000 cycles for decimal devices. A cycle is one 360° rotation.

Nominal Operating Torque: 0.006Nm

Contact Timing: Nonshorting (break-before-make)

ProgrammableIlluminated PBG

Materials & Finishes

SlidesActuator: Housing: O-ring: Base:

Movable Contact: Stationary Contacts:

Terminals: Glass fiber reinforced polyamide

Glass fiber reinforced polyamide (UL94V-0) Nitrile butadiene rubber

Glass fiber reinforced polyamide (UL94V-0) Beryllium copper with gold plating Brass with gold plating Brass with gold plating

RotariesTactiles Operating Temperature Range: Humidity: Vibration: Shock:

Environmental Data

Tilt –25°C through +75°C (–13°F through +167°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F)

10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours

50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)

TouchProcessing

AccessoriesIndicatorsSoldering:

Cleaning: Wave Soldering Recommended: See Profile B in Supplement section.

Note: During Wave Soldering process, set the switch to the following position:NDFR10, NDFR16, NDKR10, NDKR16: 0 position;

NDFC10, NDKC10: 7 position; NDFC16, NDKC16: F position. Manual Soldering: See Profile B in Supplement section.

Automated Cleaning. See Cleaning Specifications in Supplement section.

Standards & Certifications

Flammability Standards:

SupplementUL94V-0 rated housing & base

The ND Series rotaries have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit.

When used as intended in a logic-level circuit, the results do not produce hazardous energy.

G34www.nkk.com

http://oneic.com/

8mm Process Sealed DIP Rotaries

Series NDTogglesDetent mechanism designed for crisp, positive action for accurate switch setting.Bifurcated, spring loaded contacts give unmatched logic-level reliability.

Heat tolerant resin used for body meets UL flammability rating of 94V-0 and maintains switch reliability through automated soldering process.

Crimped terminals ensure secure PC mounting and prevent dislodging during soldering.

.100” (2.54mm) terminal grid spacing between pin centers,

plus 3-by-3 terminal arrangement for footprint pattern equivalent to industry standard.

Epoxy sealed terminals lock out flux, solvents, and other contaminants.

GActual Size

www.nkk.comG35

http://oneic.com/

SupplementAccessoriesIndicatorsTouchTiltTactilesSlidesRotariesKeylocksProgrammableIlluminated PBHighly visible legends and choice of screwdriver or shaft actuation to provide trouble-free code setting.

PushbuttonsSealed construction prevents contact contamination and allows automated soldering and cleaning. Sealed design accomplished with seals between the actuator and housing and between housing and base.

RockersDistinctive Characteristics

Series NDToggles8mm Process Sealed DIP Rotaries

TYPICAL SWITCH ORDERING EXAMPLE

PushbuttonsRockersNDActuatorsFKKCCircuitsRCReal Coded(White Actuator)Complement Coded (Red Actuator)101610PositionsDecimalHexadecimalPHPTerminalsStraightRight AngleProgrammableIlluminated PBScrewdriver ActuatedShaft ActuatedDESCRIPTION FOR TYPICAL ORDERING EXAMPLE

NDKC10P

Shaft ActuatedComplement Coded

KeylocksDecimal PositionsStraight PC Terminals

RotariesGACTUATORS

F

Screwdriver Actuated

120SlidesK

34Shaft Actuated

65712657TactilesActuator colors:

White for real coded

Red for complement coded

ND-FR10PActuator colors:

White for real coded

Red for complement coded

Tilt Actuators are fully rotational in either direction.

TRUTH TABLES (CIRCUITS & POSITIONS)Actuator Positionx = ON erminal No. (Output)TTouch10Decimal16Hexadecimal01234567890123456789ABCDEF1IndicatorsRReal CodedModel Numbers:NDFR, NDKR2481248www.nkk.com

AccessoriesCComplement SupplementCodedModel Numbers:NDFC, NDKCG36

http://oneic.com/

89890KND-R10P8mm Process Sealed DIP Rotaries

TYPICAL SWITCH DIMENSIONS

󰀁

(0.6).024(7.92).312(0.3).012978Series ND󰀁

Screwdriver󰀁Actuated󰀁•󰀁Straight󰀁PC

(0.3).0121C2󰀁

(2.6) Dia.1020123(0.3).012(0.25) Typ .010(5.08).2002C1(2.54) Typ .10048CC8(7.92).312(5.2).205(3.3).130(0.5) Typ.020(2.54) Typ .1004(2.54) Typ .100(0.8 ~ 1.0) Dia Typ.031 ~ .039 Terminal numbers are not on switch NDFR10P

󰀁󰀁

(0.6).024BCDEF012󰀁Shaft󰀁Actuated󰀁•󰀁Straight󰀁PC

(0.3).012(7.92).312(0.3).012(2.6) Dia.102(0.3).012(0.25) Typ.010(5.08) .2002C11C2(2.54) Typ .10048C4C8(7.92).312(3.2).126(5.2).205(3.3).130(0.5) Typ.020(2.54) Typ .100(2.54) Typ .100(0.8 ~ 1.0) Dia Typ.031 ~ .039 Terminal numbers are not on switch NDKC16P

G

(0.6).024(7.92).312(0.3).012EF012 Screwdriver󰀁Actuated󰀁•󰀁Right󰀁Angle󰀁PC

(11.0).4331C2(2.6) Dia.102(2.54) Typ .100CD(3.3).13082C14C84C(0.25) Typ .010(8.4).331(5.5).217(5.08).200 Terminal numbers are on terminal cover NDFC16H

󰀁󰀁

(3.2).126(11.0).433󰀁Shaft󰀁Actuated󰀁•󰀁Right󰀁Angle󰀁PC

(0.3).012(7.92).312(0.3).01201978(0.6).024231C2(2.54) Typ .1004C82C1(8.4).331(5.5).217(5.08).200(0.25) Typ .010(0.5) Typ.020(2.54) Typ .100(2.54) Typ .100(0.8 ~ 1.0) Dia Typ.031 ~ .039 Terminal numbers are on terminal cover NDKR10H

www.nkk.comG37

http://oneic.com/

SupplementAccessories(2.6) Dia.102

(3.3).1304C8IndicatorsTouchTilt(0.5) Typ.020(2.54) Typ .100(2.54) Typ .100(0.8 ~ 1.0) Dia Typ.031 ~ .039Tactiles456789ABSlidesRotariesKeylocksProgrammableIlluminated PBPushbuttonsRockersToggles4563456789A3456

分销商库存信息:

NKK-SWITCHND3FC16PNDFR10PNDKC16HNDFR10HNDKR16HNDKC10P

NDFC16PNDFR16HNDKC10HNDKR16PNDKR10HNDKC16P

NDFR16PNDFC10HNDFC16HNDKR10PNDFC10P